ASTM A 519-06 Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing.pdf
ASTM A 519-2006 Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing.pdf
ASTM A 519-1996 機械用碳鋼和合金鋼無縫鋼管 中文版.pdf
ASTM A 519-2003 Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing.pdf
ASTM A 519-2006 無縫碳素鋼與合金鋼機械管(中文).pdf
ASTM A 519-89_ASME SA519 SEAMLESS CARBON AND ALLOY STEEL MECHANICAL TUBING.pdf
ASTM A 519-96 Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing-英文版.pdf
ASTM A 519-96《機械工程用碳素鋼和合金鋼無縫鋼管》-中文簡要說明-.pdf
#無縫鋼管# #鋼管生產# #鋼管加工# #鋼管標準# #碳鋼# #合金鋼# #下載#
以上下載，需要注冊為：知識星球會員。
Scope
1.1 This specification covers several grades of carbon and alloy steel seamless mechanical tubing. The grades are listed in Tables 1-3. When welding is used for joining the weldable mechanical tube grades, the welding procedure shall be suitable for the grade, the condition of the components, and the intended service.
TABLE 1 Chemical Requirements of Low-Carbon Steels
|
Grade Designation |
Chemical Composition Limits, % |
|||
|
CarbonA |
ManganeseB |
Phosphorous,B |
Sulfur,B |
|
|
|
|
|
|
|
|
MT 1010 |
0.05–0.15 |
0.30–0.60 |
0.040 |
0.050 |
|
MT 1015 |
0.10–0.20 |
0.30–0.60 |
0.040 |
0.050 |
|
MT X 1015 |
0.10–0.20 |
0.60–0.90 |
0.040 |
0.050 |
|
MT 1020 |
0.15–0.25 |
0.30–0.60 |
0.040 |
0.050 |
|
MT X 1020 |
0.15–0.25 |
0.70–1.00 |
0.040 |
0.050 |
TABLE 2 Chemical Requirements of Other Carbon Steels
|
Grade Designation |
Chemical Composition Limits, %A |
|||
|
Carbon |
Manganese |
Phosphorous, |
Sulfur, |
|
|
|
|
|
|
|
|
1008 |
0.10 max |
0.30–0.50 |
0.040 |
0.050 |
|
1010 |
0.08–0.13 |
0.30–0.60 |
0.040 |
0.050 |
|
1012 |
0.10–0.15 |
0.30–0.60 |
0.040 |
0.050 |
|
1015 |
0.13–0.18 |
0.30–0.60 |
0.040 |
0.050 |
|
1016 |
0.13–0.18 |
0.60–0.90 |
0.040 |
0.050 |
|
1017 |
0.15–0.20 |
0.30–0.60 |
0.040 |
0.050 |
|
1018 |
0.15–0.20 |
0.60–0.90 |
0.040 |
0.050 |
|
1019 |
0.15–0.20 |
0.70–1.00 |
0.040 |
0.050 |
|
1020 |
0.18–0.23 |
0.30–0.60 |
0.040 |
0.050 |
|
1021 |
0.18–0.23 |
0.60–0.90 |
0.040 |
0.050 |
|
1022 |
0.18–0.23 |
0.040 |
0.050 |
|
|
1025 |
0.22–0.28 |
0.30–0.60 |
0.040 |
0.050 |
|
1026 |
0.22–0.28 |
0.60–0.90 |
0.040 |
0.050 |
|
1030 |
0.28–0.34 |
0.60–0.90 |
0.040 |
0.050 |
|
1035 |
0.32–0.38 |
0.60–0.90 |
0.040 |
0.050 |
|
1040 |
0.37–0.44 |
0.60–0.90 |
0.040 |
0.050 |
|
1045 |
0.43–0.50 |
0.60–0.90 |
0.040 |
0.050 |
|
1050 |
0.48–0.55 |
0.60–0.90 |
0.040 |
0.050 |
|
1518 |
0.15–0.21 |
1.10–1.40 |
0.040 |
0.050 |
|
1524 |
0.19–0.25 |
1.35–1.65 |
0.040 |
0.050 |
|
1541 |
0.36–0.44 |
1.35–1.65 |
0.040 |
0.050 |
1.2 This specification covers both seamless hot-finished mechanical tubing and seamless cold-finished mechanical tubing in sizes up to and including 12 3/4 in. [325 mm] outside diameter for round tubes with wall thicknesses as required.
1.3 The tubes shall be furnished in the following shapes, as specified by the purchaser: round, square, rectangular, and special sections.
1.4 Supplementary requirements of an optional nature are provided and when desired shall be so stated in the order.
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets or parentheses. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. In this specification hard or rationalized conversions apply to diameter, lengths and tensile properties. Soft conversion applies to other SI measurements.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Keywords
alloy steel tube; carbon steel tube; mechanical tubing; seamless steel tube; steel tube;
ICS Code
ICS Number Code 23.040.10 (Iron and steel pipes)
DOI: 10.1520/A0519_A0519M-17
下方下載 可以直接下載，不需要注冊會員：
| 1 | ASTM A519-96 Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing-英文版 |
| 2 | ASTM A 519-2006 Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing |
| 3 | ASTM A519-96《機械工程用碳素鋼和合金鋼無縫鋼管》-中文簡要說明- |
| 4 | ASTM A519-1996 機械用碳鋼和合金鋼無縫鋼管 中文版 |
| 5 | ASTM A519-2003 Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing |
| 6 | ASTM A519-89_ASME SA519 SEAMLESS CARBON AND ALLOY STEEL MECHANICAL TUBING |
| 7 | ASTM A519-2006 無縫碳素鋼與合金鋼機械管(中文版) |
